I tried to make "GMT style" for the first time in a long time(Inspired by Mr. Daichi) Both are cases of namoki、Other parts will be transplanted or reprocessed from the previous one, so I will omit the details ww Chuder(チュード〇ル？)It's the wind。 Initially under the crown of Crown? I scraped it and put an appropriate O-ring in the gap to make it look like a "big crown".、It was rejected because the movement of the crown became strange.。 GMT mass 〇ter style。(It is a specification that the lug width and the breath width do not match w) Initially, the case, bezel, etc. were combined differently.、Above all, the method of fixing the GMT hand was different.。The root of the short hand(Is it a ring?)I used to wear the GMT stick part with "instant adhesive"、It's a blunder that you can get it in about a week and you don't notice it for about half a day。 There is a shocking sight that the second hand keeps pushing the GMT hand, which was stuck between the long and short hands, with 6 beats ...(↓ is before it can be taken) this time(I forgot to take a photo w)Has scraped off the hakama of the GMT needle and widened the shaft hole with a stick file and inserted it into the hakama of the short hand.。It seems that it will not come off if it is a little shock、Since the clearance with the dial is also taken, the index where the letters are planted can be avoided with a margin.。 While I am ... I'm doing Mendokusai ww

I replaced the previously posted "Several Boys" with an external case.。 New parts case、Bezel、Chapter ring：namoki crown：watch & style From here on, it's my memorandum (feature) It was a strange case because it was an outside case that day.。First of all, I shook the windshield without putting the chapter ring in the check (the photo is an image) I regained my mind and put the chapter ring and shook the windshield again But something strange ... It is out of focus, but this chapter ring is around 12 o'clock Is distorted。Because there is an alignment dent around 12 o'clock。And it's also around 8 o'clock。Did you understand? I completely forgot that there was an alignment protrusion on the back of the chapter ring, and I put in an appropriate "chareen" and rubbed it.。 I thought I wouldn't see it, but my conscience didn't allow me to try the windshield again.。However, I still didn't realize that this was a hint of the tragedy that would come later ... With my broken heart in my chest, I smashed the board and put it in a case.、If you check that there is no dust or dirt on the board before tightening the back cover, it will make you feel uncomfortable again ... The index is off the center of the case (the photo is an image). I thought, but the calendar looks good.。Hello! If you look carefully, the mechanism moves left and right inside the case.。 The black spacer (thick) and the regular 5 gray spacer (thin) have different crown tube openings.。Apparently, the protruding part inside the crown tube of the namoki case seems to be the same size (thin) as regular 5.。 9Replace the spacer (black → gray) and redo the board again to inspire the broken heart。 This time there is no rattling。Come on, just as I'm gonna close the back cover ... I won't close it! ?? If you look closely while calming the heart that is connected to one piece of skin on the neck, the first and second steps of the female screw on the case side are distorted.。That's right foreshadowing。 Before I got here, I had to redo the windshield many times.、It seems that a small diameter was inadvertently used for the pressing piece of the pusher, and that piece pushed the screw groove pinpoint.。 I was completely broken。 A few days after we started to consider disposal。When squeezing other cases with a leutor, "! You should scrape off the distorted screw groove!" Remove the windshield in consideration of the shavings (at this point, finally decide on a new windshield packing). Lid alignment、I scraped it and repeated the lid alignment and managed to complete the deadline (although I screwed it in at the end) I asked for the wrong color of the back cover ww Oops the bezel was still there。With the pusher, "Pakin" → "I forgot to insert the spring!" "Pakin" → Durara r- "I forgot to insert the o-ring!" "Pakin" → Gununu n "Ah! The o-ring is sticking out!" "× 3 It was a mess, but if it's over, everything is fine ... No、It feels strange ...