White was custom made want。
Dial using the skz323、Bezel insert LCBI
Windshield purchased from crystaltimes
Movement：NH36A (4R36 corresponding product)
With a hack function
skx007 MOD custom white diver
SEIKO 5 .club
Anyone MOD information posting site can post!
skx007 MOD custom white diver
Mr. sco3601! Long time no see! ^^
And、First post、It has indeed、Thank you!
There is as long as I'm happy!
so、Indeed refreshing、It is a beautiful diver!
Since the precious image is hard to see small that it from the PC、Nosy while、We've made larger。
Since Mr. sco3601 is such you have a story a lot、m thank you in the future(_”_)m
Manager's、Long time no see。
Thank you for adjustment。
clock、From now on we will continue to up little by little because there is a variety。
Also、I look forward to working with you。
sco3601 like
Nice to meet you、White dial、Iiｰ is Nee。Among the basic black and white、In the way of one point of second hand destination of vermilion marker is pointing color、I am impressed and has become a good accent! !
by the way、skz323 because gradually the dial (Stargate system) of (plate two-ply?)、SKX007;9Case (and、And attached to the accessory chapter)、The bulk amount on the front side of the day、Move is extruded and since shifted to the center of the crown-Chuvu、The winding stem I think that does not come to the true core but was seen in the verification example of watch blogger's a ··· ← certain enthusiast。(The person who had been corresponding lack 0.5mm thickness the SKX chapter in trimmer)
What would the technique was used?、I hope you can tell me worrisome。
Nice to meet you、
I had to check when you are actually attached、Mine is probably so much so that the deviation did not。
Because it is also changing chapter ring whether the compatibility with there was good?
Even with attached、Special、You have to use and usually because there is no Toka bad movement of the crown。
Movement、I do not think too deeply because the problem will be replaced immediately to the Toka NH36 if at people who do not put up for basic OH。
sco3601 like
Immediately your answer、Thank you。Oh really! So it individual to compatibility was good。I see。
Since the direction of Kudan blog was intact chapter was attached to SKX、I wonder if compatibility with it there was bad? Now reference。There is going to be mounted soon SBDC039 of the dial (2 plates state at the outer peripheral + time planted together) to SKX、I've just been thinking。
by the way、Exchange of each Mov't of OH instead、I feel the same way。(Cost-effective as well)
Please be once in reference because I remembered that I was thinking。
0.5I think that good to mm thick measures'll cut degree 0.4 Turn so as to draw a round and round circle the top of the chapter ring on top of the water-resistant paper of about No. 1200 as。
For comparison、0.4I think mm cut becomes is so because the lower side of the projections of the chapter ring (positioning) it takes less work because the clearance even after you put the crystal becomes wider、Fit while confirming that it is in the proper position when fitting the move、After that I think that I can quietly mounting (slowly) without projection is displaced and will turn the back cover。
Again of your professor、Thank you very much。
Actually、Questions and parallel (preceding) to、My own to had been the practice to imitate to put a notch in the previous chapter the lower back。... is I have to cut the raised dot part by mistake at the end of the stage。
Aimed at the middle position of the bank width in the circumferential cutter、Pull the boundary、As measured in Depusuba to sober Iｰ、... the results many times by cutting the surface to the horizontal in the Tairakin cutter、Per hour planting the outer verge unit was able to temporarily assembled with the feeling that is compensated for as tenon joint。(I only try to the casing, but ...、What I wonder to become)
Chapter、Because there is still a number of Tama、It is Ya might also be tried when so did not go well。... really very much。
Tool was what our like this。
Potch part、We are playing with putty (wispy、）
I've worked hard。
Well go and I hope 😊
In the description on the Supplementary、0.4Although I have wrote a shaved mm、0.5Since it is a mistake of mm、I'm sorry。
Since the upper side of the chapter ring invisible refracted if stuck in Crystal、I think that nice and easy。
Draft of water-resistant paper、Turning round and round over the platform that is out of plane、I think that it does not become strangely diagonally。
Please refer to because I think processing also that it is easy to。
Is the sequel!
Result、It went well!!···But、SBDC039 (Transocean) is the crown 21 minutes + 30 seconds? Because it was for the position、We've shifted about 2 minutes in a counter-clockwise。(Reflection) also、It is the zodiac change。
thank you for helping me。(_ _)
※ but was more information sent was croton to Members、It does not seem to be reflected。
It is finished a little after processing also seems to have gone well。
Please be unveiling Once you have completed。
I am looking forward 😊👍