It is SNK357 revived in an external product case。
I like the beautiful dial、SNK357 obtained from junk。
Navy blue with blind shield marks
Navy blue with blind shield marks
Custom parts are as follows
-Movement：4Navy blue with blind shield marks
-Navy blue with blind shield marks：Ariek
- 3 stitches：Ariek
- text plate：Navy blue with blind shield marks
-Navy blue with blind shield marks：Ariek
Navy blue with blind shield marks
Navy blue with blind shield marks。Of course、The day car is in Japanese。
This dial is 4 o'clock and the position does not match in the new case、
I cut the zodiac legs。When disassembling the double-sided tape again
When disassembling the double-sided tape again、I am reattaching the new zodiac legs to the 3 o'clock specification。
When disassembling the double-sided tape again
When disassembling the double-sided tape again、Sometimes there is a loss,、
It's kind to your wallet and it helps ☆
When disassembling the double-sided tape again、Nice to meet you。When disassembling the double-sided tape again、When disassembling the double-sided tape again
Also、When disassembling the double-sided tape again、When disassembling the double-sided tape again
Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away。
Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away
Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away。thank you for your comment。Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away
Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away、I will refer to it in various ways.。
I have to reattach the zodiac legs that you inquired about.、Not solder。
The heat of the solder discolors the dial、I gave up。I'm a two-component type
It is attached with epoxy adhesive.。To the extent that it is attached to the movement
It is firmly adhered so that it can not be removed at all。
Once、It is firmly adhered so that it can not be removed at all。It is firmly adhered so that it can not be removed at all
It is firmly adhered so that it can not be removed at all。
It is firmly adhered so that it can not be removed at all。
It is firmly adhered so that it can not be removed at all、It is firmly adhered so that it can not be removed at all。
Two-component epoxy adhesive and a file are surely the secrets of strength.。
I will try it next time when I have the opportunity to glue the zodiac legs。Thank you for telling me!
Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away
Adhesion of zodiac feet Please try it by all means.。Pray for success
We are doing ☆
I am also looking at ichi's work! Vintage processing
I am also looking at ichi's work! Vintage processing。
I am also looking at ichi's work! Vintage processing、I am also looking at ichi's work! Vintage processing
I am also looking at ichi's work! Vintage processing。
I am also looking at ichi's work! Vintage processing。
The retrofitted zodiac is like a thumbtack! saw it for the first time! !!
I am a double-sided tape fixed group for all dial changes from 3 o'clock to 4 o'clock and 4 o'clock to 3 o'clock。
、This is because the zodiac legs are often bent or fine, or "misaligned" in both external and genuine products.。
So ... cut the zodiac legs "to some extent" and align them, then press the dial strongly against the spacer.。
So ... cut the zodiac legs "to some extent" and align them, then press the dial strongly against the spacer.
YOSHIPI- like
That's right。The retrofitted zodiac is like a thumbtack! With solder
When you're having a hard time、It's small, but I thought it would be nice to draw、In AliExpress
When I found it, I was ecstasy!
There was a time when I worked hard with double-sided tape,、I had a hard time disassembling it again、
I became a zodiac foot replantation group。
I became a zodiac foot replantation group
I became a zodiac foot replantation group
I became a zodiac foot replantation group
I became a zodiac foot replantation group
I became a zodiac foot replantation group。
The index is also glittering and I thought that the dial of the SNK35 series was beautiful and collected it.、I have a lot for some reason w
It's also an ant to be in the divers!
SHUKU like
thank you for your comment。That's right。I like this dial!
As commented by SHUKU、The index is also glittering、Divers'
From the case、From the case
From the case。
It's cool、Dial、Case、From the case。
Earth
thank you for your comment。From the case
From the case、From the case、From the case
From the case、I bought this case complete set for the time being
Landing。
If you find navy blue with a beautiful aluminum bezel insert, change it
Maybe (laughs)
Nice to meet you。
I didn't know there was an aftermarket zodiac foot。What should I search for on Aliek to find it?
Mr. taka
Is it solder? If so, did you take great care in adjusting the heat to prevent discoloration of the blue dial? I tried it with Gorilla Glue & Bondic in the past, but I got it right away。Thank you。
sorry for the late reply。As for the zodiac foot that you inquired about later,、
Watch Dial Feet in English。Please refer to the link below。
https://www.aliexpress.com/item/1005001860138248.html?spm=a2g0o.order_list.order_list_main.373.63d21802rD74Rh
How to install is my own、I glued with epoxy resin。
The thickness of the adhesive will increase, so it is better to make it as thin as possible.。
If it is too thin, it will be easy to remove the zodiac legs.、It's difficult to adjust。
Actually, the back side of the dial is scraped off by the seat of the zodiac foot, and then the adhesion is done.
seems correct、As mentioned above, there is no particular problem (for now)。
We will also show you a video about this scraping.、
If you don't mind, please let me know。
https://www.youtube.com/watch?v=9F7V0vTvUwI
I pray that taka's mod will go well。
Tak961
Thank you very much for letting me know the link。
I don't have the courage or skill to cut down to the seat surface, so I'll try Tak's pattern with epoxy.(Lol)
I think the positioning is severe. Do you have any tricks?
Mr. taka
sorry for the late reply。
Positioning is really tough。I attach the zodiac foot to the movement holder first
Keep、Put some epoxy on it、Like putting a dial on top of it
is positioned by。
because it is set up、Not suitable when porting the dial to another movement holder
Although there may be cases、for your information。